X2 |
X1 |
Y2 |
Y1 |
Output |
0 |
1 |
0 |
1 |
0 |
0 |
1 |
1 |
0 |
1 |
1 |
1 |
1 |
1 |
0 |
Design and simulate (you do not need to simulate if you don't have the Logisim software)...
Using logisim to create a 4bit controlled comparator ECFICATIONS NPUTS Create a cireuit in Logisim thait will take the following inputs 4 bit binary number :4 bit binary number Control where C-O, A and B will be treated as unsigned binary C-1,A and B will be treated as 2's complement signed binary (for example, the number 301 represents the value 5' it is treated as unsigned binary but it represents the value - if it is treated as 2's complemene...
8. For this problem, you are to design a simple combinational logic circuit and then use Logisim to simulate and test the circuit. The circuit is a 2- bit priority encoder with inputs X2 and X1 and outputs Y1 and Yo. The circuit behaves as follows: oIf X2X1 00, then Y1Yo 00 (no active input) If X2X1 01, then Y1Yo = 01 (low-priority input, X1, is active) If X2X1 1-, then Y1Y0 10 (high-priority input, X2, is active) Note that...
(Don't do the simulation If you don't have LigoSim to simulate) I appreciate your efforts and time in advance! a)Simulate and test a 1-bit full adder. Use 2-input exclusive OR gates to realize Sum. Use an SOP form to realize Cout b) Simulate and test a 4-bit adder circuit using serially interconnected 1-bit full adder sub-circuits. The adder will be able to add 4 bit positive numbers and should be able to add 15 and 15 to get 30. c)...
The circuit on the bottom is the logisim file A B C D x о o 110 0 1 0 1 0 1 1 1 1 1 1 о ное o o o | o o 1 o 1 | 1 0 1 b. Enter the Boolean algebra expression for the circuit seen in the Logisim file. Enter the expression EXACTLY as the circuit is drawn and NOT the expression that would be obtained from the truth table or from...
Show all steps of your solutions. Attach screen shots of your Logisim Solutions. Solutions without clear solution steps will be subject to maximum penalty I. Assume that A 100 in hexadecimal and B = 25 in octal. Perform the indicated operations: a. A - B using 2's comp b. B- A using 10's comp 2. Write Institute of Electrical and Electronics Engineers (IEEE) floating point (32 bit) representation of the decimal number -100. 625 lement method lement method 3. Design...
Need help with this digital logic problem please show work for all parts thanks [2] [20 points] A 2-bit Binary Comparator logic circuit receives 2-bit numbers, P = P.P, and Q = Q.Qo, and has three outputs Y2, Y1, and Yo: Output Y2 is 1 if and only if P < Q, otherwise it is 0. Output Y1 is 1 if and only if P > Q, otherwise it is 0. Output Yo is 1 if and only if P...
Design a circuit to add two 2-bit binary numbers and display the results of the addition as a 3-bit binary number, with the most significant bit be the carry out. To do this, you will use the four switches on your Breadboard Companion as your two 2-bit number inputs. Three of your LEDs will be used to represent the 3-bit output of your circuit. Complete a truth table for the expected output values on the lab data sheet attached. Use...
In this problem, you will design a 4-bit 2's complement sub tractor, implement it in Logic works, and test it. The 4-bit sub tractor works as follows: given two numbers X and Y in 2's complement binary representation on 4 bits, it outputs a 4-bit value representing X - Y in 2's complement. To obtain full marks, the following requirements must be met: You are only allowed to use basic gates, including NOT, AND, OR, NAND, NOR, XOR, XNOR. (You...
DESIGN SECTION Before the experiment, you are going to design a circuit which has 4 inputs w, x, y, z and an output F. If 4-bits input value is “odd number which is higher than 4”, or “3-bits highest even number” or “4-bits highest even number”, the output function F will be equal to 1. Otherwise F=0. Each students have to design the circuit and have to do following steps own by own. You are going to; a) Fill the...
3.4.1 Build and simulate the comparator circuit shown in Figure 3, in Multisim. The inputs A3, A2, A1, 40 act as the first 4-bit binary number, and B3, B2, B1, BO act as the second 4-bit binary number. Run your circuit for different setting of the inputs as in Table 3 and observe how the output Xchecks if the numbers are equal or not. Note: connect the eight inputs of this circuit to an 8-input DIP switch as shown in...