*For a clearer view of the datapath*
Answer choices for all
instruction : andi $t0, $t1, 4
control signals
RegDst = 1
Jump = 0
Branch = 0
MemRead = 0
MemtoReg = 0
ALUOp = 000
MemWrite = 0
ALUSrc = 1
RegWrite = 1
*For a clearer view of the datapath* Answer choices for all Consider the MIPS single cycle...
Q4: Answer the following questions. [7 Marks] The single cycle implementation of MIPS is as shown below. Answer the following questions with reference to "beq $S1, $S2, 8H” instruction. Assume that the contents of the registers S1 = 10 H, S2 = 10H, and PC = 16H, pointing to the instruction under consideration. 1. What is the addressing mode of the instruction? [1] ii. Which part of the instruction format, address of S1 and S2 are stored? [1] 111. What...
Assume that ‘slt $1, $2, $3’ is executed with the implementation in the picture. Identify the value of the 9-bit control signals. Add u X ALU result 4 Add Shift left 2 RegDst Branch MemRead MemtoReg Control ALUOP Instruction [31-26 MemWrite ALUSRC RegWrite Instruction [25-21] Read register 1 Read Read PC address Instruction [20-16] data 1 Read Zero register 2 Instruction ALU ALU 31-0] Instruction memory Read data M Read Address Write result u M Instruction [15-11] register data 2...
A block diagram of MIPS architecture is given below. What is the value of the control bit for each MUX during the execution of the given instruction? Note, you may use N/A if MUX output is not useful. Add MUX 4 ALU Addresult Shift left 2 RegDst Branch MemRead Instruction (31-26] MemtoReg Control ALUOp MemWrite ALUSrc RegWrite Instruction [25-21] PC Read address Read register 1 Read Read data 1 register 2 Write Read MUX 2 Zero Instruction (2016) MUX(1 Instruction...
6. Consider a datapath similar to the one in figure below, but for a processor that only has one type of instruction: unconditional PC-relative branch. What would the cycle time be for this datapath? PCSrc Add ALU Add result Shift +( left 2 Read register 1 ALUSrc, 4 ALU operation PCRead PC-address Read data 1 Registers Read data 2 MemWrite Zero ALU ALU-I Address MemtoReg Instruction register 2 Instruction | Write Read data-M register Write Lu memory Write Data data...
it is the same question A block diagram of MIPS architecture is given below. What is the value of the control bit for each MUX during the execution of the given instruction? Note, you may use N/Aif MUX output is not usefu Add MUX 4 ALU Add, result Shift left 2 RegDst Branch MemRead Instruction (31-26] Control Memto Reg ALUOP Mem Write ALUSrc RegWrite Instruction [25-21) PC Read address Instruction (20-16] MUXT Read register 1 Read Read data 1 register...
(o x Add Addresult ALU Shift left 2 Regst Branch MemRead Instruction (31-26) MemtoReg Controll ALUOP MemWrite ALUSC RogWrite Instruction [25-21] Read register 1 Read Instruction (20-16) Read data 1 register 2 Write Read Instruction (15-11) Write data Registers PC Read address Zoro ALU ALU Instruction (31-0) Instruction memory result Address Read data register data 2 **039 -25 Write Data data memory Instruction (15-01 16 Sign- extend ALU control Instruction 15-01 With regards to the single cycle implementation (as shown...
Question 5 0.25 pts What is the value of the MemWrite control signal? Question 6 0.25 pts What is the value of the ALUSrc control signal? Add Add Sum--(1 4 Shift left 1 Branch MemRead Instruction [6-0] ControMemtoReg MemWrite ALUSrc RegWrite Instruction [19-15]Read Read register 1 Read Read data! PCaddress Instruction [24-20] Zero ALU ALU result register 2 Instruction 31-0 Instruction [11-7 Read1 Address data | Write Read register daiaALU | M Instruction memory Write data Registers Write Data data...
Question 4: Single Cycle Datapath Control (15 points) We wish to add the hardware support for a special R-type instruction jlr Jump and Link Register) to the single-cycle datapath below. Though this is an R-type instruction, but it is a special one that has the opcode being 000001 (instead of 000000), so the control unit will be able to differentiate this jlr instruction from the other R-type instructions and generate a special set of controls for this instruction. Opcode rs...
How would the multicycle MIPS design support the jr instruction? Show the machine code format and your solution should describe any new datapath features and control changes to the finite-state diagram below (this may include adding new states). Information for problem1 0 Instruction Fetch 1 Decode/Register Fetch 2 Address Calculation 3 Memory Read 4 Write-back Step 5 Memory Write 6 R-execution 7 R-completion 8 Branch completion 9 Jump completion O Mem Read ALUSelA 0 ALUSelB 01 lorD 0 ALUOp 00...
Modify the circuit to support a MFCC instruction. MFCC Rd instruction: Move From Condition Codes MFCC copies into the four rightmost bits of Rd the values of the ALU signals Carry (C), Overflow (O), Zero (Z) and Negative (N) as they were set by the previous R- type instruction. The remaining 28 bits of Rd are set to zero. Describe the changes and additions needed for the single-cycle MIPS processor datapath and control to support this instruction. Hints: 1) MFCC...