Please provide answer in nearest 4 decimal places. Please provide units. Question 59 (1 point In...
Please provide answer in nearest 4 decimal places. Please provide units. Question 31 (1 point) In a right angle, AB-2 m, and angle ACB is 63.43 Degree. A point charge of 2" 19 nC is placed at point A and another point charge -3" 19 nC is placed at point C. Calculate the POTENTIAL at B Your Answer Answer Question 32 (1 point) 2 charges, 19.33 μC each, are located at two vertices B & C of an equilateral triangle...
PLEASE ANSWER ALL QUESTIONS. ROUND ANSWER TO THE FOURTH DECIMAL PLACE WHEN NEEDED Question 12 (1.5 points) R2 R1 R3 R5 M W R4 In the following circuit, R1=13 Ohm, R2=4* 4.0 Ohm, R3=4* 4.0 Ohm, R4=2* 4.0 Ohm, R5=13 Ohm and E= 13 Volt. Calculate the current in R5 resistor. [Picture File-Ohm-2.jpg] Your Answer: Answer units Question 13 (1.5 points) R2 R1 R3 R4 M E In the following circuit, R1=0.8*6 Ohm, R2=2* 6 Ohm, R3=3* 6 Ohm, R4=2*...
PLEASE ANSWER ALL QUESTIONS. ROUND ANSWER TO THE FOURTH DECIMAL PLACE WHEN NEEDED Question 9 (1 point) CZ CI 11c3 G C5 In the following circuit, C1=5.7 F, C2=2*5.7 F, C3=2*5.7 F, C4=2*11.4 F, and C5=3*11.4. Calculate the equivalent capacitance in the circuit. Your Answer: Answer units Question 10 (1 point) AR-C series circuit is connected to a 12 volt battery. Initially the capacitor has zero charge. Assume R= 17 12, C= 1,043 uF. When the circuit is closed, calculate...
It Kind of goes without saying but if you have no knowledge than dont comment or try and answer this question you dope Questions 1-3 below are about the amplifier circuit of Figure 1. Here Vcc is a fixed voltage The base voltage vB(t) is time-varying, and is of the form vB(t) V(t) where VB is a DC offset, and vb(t) is a time-varying purely AC signal. Suppose the amplitude of vb is A. Assume that the capacitor C is...
Please, answer to the following questions based on the diagram provided. 1)Why is it L/R not LR for the charging and discharging a series RL circuit? 2) In the determination of C in part II, what will you obseve if the voltage probe was connected across decade resistor Rd? Can you determine capacitance from this? (During the experiment we connected voltage probes across capacitor) 3) In the determination of L in Part III, what will you obseve if the voltage...
PLEASE ANSWER VERY QUICKLY!! I RATE HIGH!! The experiment is on RC circuits and the aim is to determine the time constant. Your group sets up the circuit with a resistor R and a capacitor C connected to a switch and an ideal battery (E). The circuit diagram is shown in the figure. You close the switch at time Os and the voltage across the capacitor Ve and current I in the ammeter are recorded in a spreadsheet using a...
please choose one of the answer choices above. Must show all work, thank you Question 4 CIRCUIT B2 (2.5 Marks) +Vcc Rc IRC Vic RB Ів Vc VB VE RE IE FIG.4: CIRCUIT B2 Statement: Sketching relevant output (Vc-Ic) characteristics decide on Q-point coordinates and DC load-line details: That is, determine DC operating conditions of the NPN-BJT/Si circuit of Fig.4 (denoting the type Circuit B2). Assume the following: Vcc= 24 volt; Rc = 5.0 k; RE = 1000 ohm; RB...
45 T or F The most common linear circuit is the amplifier circuit 46 T or F Both a resistor and a diode are linear devices. 47 I or F A high pass filter on the output of a rectifier is commonly used since you want to block DC voltages and keep high frequencies 48 T or F If the voltage across a one ohm resistor is one volt, the current is 1 A 40 T A LL graphs must...
please pick one of the multiple choice options above. show all work, thank you Question 9 CIRCUIT X/FIG.9 (5 Marks) Statement: Consider the RC-coupled amplifier circuit illustrated in Fig. 9 (CIRCUIT X). Sketching relevant output (Vc-Ic) characteristics that decide Q-point coordinates and DC load-line details (of the NPN-BJT/Si circuit of Fig. 9 of Circuit X) Further, establish an appropriate AC-load line and decide the maximum swing of the output voltage across Rload with respect to the Q-point. Assume the input...
please choose one of the answer choices above. Must show all work, thank you! Question 8 CIRCUIT D.2 (2.5 Marks) Statement: Sketching relevant output (Vc-Ic) characteristics decide on Q-point coordinates and DC load-line details: That is, determine DC operating conditions of the NPN-BJT/Si circuit of Fig.8 (denoting the type Circuit D2). Assume the following: Vcc= 10 volt; VE = 1.8 volt; Rc = 2.0 k; RB2 = 25 k and a = 0.98958. +Vcc Rc IRC RB1 INIC 11 IB...