Question

is that possible we could make arc reactor in small size ? in reality like movie of iron man ? if yes so how ? because I seen that all process on internet but it's a big like a computer CPU .... please explain for my knowledge .good if you share lil more deeply with drawing

Answer 1

There are a few necessary tools:
soldering iron
dremel tool
drill bits
metal snips/shears
jeweler's saw (or some kind of saw to cut metal and plastic)
needle nose pliers
wire cutters
files/sandpaper
glue gun

And for materials:
thin brass sheet
plastic sheet ( I used Delrin- you can buy Delrin and acrylic sheet from Colorado Plastics)
clear acrylic sheet
copper wire- 22ga and 24ga thickness solid wire
sheet metal- 22ga thickness (.025in or about .5mm thickness)
PCB (printed circuit board)- at least 4" square (Radio Shack sells some that measures around 4.5" x 6")
several small bolts - I used 10ea 2.5mm bolts and 3ea 3mm bolts w/nuts
3 volt battery
11 ea NTE30027 surface mount LED's - I bought them from a local supplier but you can order them here:
I'll make specific notes about the materials used and possible substitutes/workarounds on the specific construction pages.

Please note: be careful cutting sheet metal as the edges can be very sharp and it's pretty easy to cut yourself.

Step 2: Start With the Backplate

a: 0

36 Apmir 30

.330

The first thing I did was draw up a general plan so I could figure out how everything would fit together. The outer diameter of the Arc Reactor is 4", so if you print the plan photo to that scale it will give you a good guide and help you get everything lined up correctly. All the measurements used in the drawings are in inches and they are really just to be used as a guide- I really just eyeballed everything as I was making it. By no means are they meant to be exact measurements. The most important thing is getting the proportions correct so everything will fit together during the final assembly.

The easiest way I found to cut out all the parts is to draw the patterns on paper and then glue the patterns to my sheet plastic or sheet metal using rubber cement and cut the patterns out with a jeweler's saw. Then file all the edges and smooth them with sandpaper.

So let's start by making the outer ring/backplate assembly. Begin by cutting a 4" diameter disc from PCB material. There are two copper traces cut (or etched) into this as well as a couple of solder pads on the center so you can solder down the LED's. There are 11 LED's- 10 for the clear ring and one for the center lens. The LED's I used are a surface mount type part# NTE 30027. Even though they are a surface mount component they are pretty easy to solder to the copper traces.The LED's sit directly under a clear acrylic ring and they are spaced 36 degrees apart- just make sure they are all facing the same direction! I simply connected the LED copper traces to the center solder pads and then drilled two small holes and soldered some wires from the back of the board to go to my 3v battery.

UPDATE!
Instead of having to make a circuit board and solder all the tiny LEDs you can just get some of these little guys and wire them in parallel-
http://www.sparkfun.com/commerce/product_info.php?products_id=8735

Just glue them down to a back plate and you're good to go!

The outer ring was cut from some thick plastic sheet- I used Delrin because it cuts well and is pretty durable. A good substitute would be 1/2" MDF sheet. I should have painted the ring silver but I ran out of time......maybe I'll make a machined aluminum ring in the future. There are 10 2.5mm allen head bolts evenly spaced at 36 degree intervals around the ring. I just drilled a pilot hole, then drilled a countersink for the bolt head so it would sit just below the surface of the ring. I actually threaded the holes for the bolts but you could probably just shove them in there with a bit of glue.

The outer ring is glued to the PCB backplate with a hot glue gun. Then run a bead of hot glue over the LED's and the copper traces. This will protect the LED's, help diffuse the light and keep the circuit from being shorted out when the remaining parts are installed.

Now you need a lens for the center. I made mine from acrylic sheet, but you could use just about any kind of lens or clear plastic part that would fit. The thing to remember is that if it is too tall then it will come into contact with other parts later on so watch the height. I used a scotchbrite pad on the lens to help diffuse the LED light.

Next an old heart rate monitor strap was glued and screwed to the backside of the backplate. The two screws went through the PCB and into the outer ring, helping to hold everything together.

Step 3: Make the Inner Ring Assembly

Now we have to make the inner ring. This is a clear ring that is held by a frame (which I call the lower spider frame.)

First cut the inner ring from clear acrylic sheet and rub it with a scotchbrite pad (steel wool would also work.)

Now comes the tedious part- there are 20 arms that need to be cut out, bent and then placed around a central ring to form the lower spider frame. The dimensions on this are not critical, but you have to constantly check the fit so that it will fit into your previously constructed backplate assembly. You also have to make sure that the clear ring will fit into the slots cut into the spider arms.

The distance from the outer edge to the opening of where the large notch is approximately .08 inches. The trick is that you will have to adjust the fit of this to your acrylic ring as well as the outer ring. You want the spider to essentially press fit snug into the outer ring. Then fit the acrylic ring to the spider. I can guarantee that you will probably have to do some trimming because the spider is so difficult/frustrating to make so that everything is aligned properly. I had to trim probably every opening to get everything to fit properly.

The easiest way to trim the opening in the spider is to use a small sanding disk with a Dremel tool to carefully trim the opening to fit the acrylic ring. The acrylic ring doesn't have to be a perfect fit as it's held in place by the copper wire wrapped around it.

I cut both the central ring and spider arms from 22 ga sheet steel using sheet metal shears and a jeweler's saw. A dremel tool would also work and will come in handy cleaning up all the rough edges. The finished arms were then welded to the central ring. Then the center bottom ring was cut from steel sheet and welded to the spider frame assembly- note how it is positioned. I was short on time so I left out the additional slots. The bolt holes were threaded for 3mm bolts.

As a substitute for sheet steel you could make the parts from brass or copper sheet and then solder the arms to the central ring and then solder the central bottom ring to the spider frame assembly.The parts could also be made from thin plastic sheet as well and just glued together, but they wouldn't be as durable.

Now you have to make 10 little brass tab thingies. These sit on top of the clear ring after it has been placed into the spider frame assembly and then they are then wrapped with 22ga copper wire. Make sure when you wrap the wire it doesn't stick out too far outside the spider frame arms- make sure to check the fit with the backplate assembly- mine is just a light friction fit. The brass tab thingies should be about the same width as your clear ring and the four little tabs should just stick out over the edges of the spider arms. The last bit is to solder some short 24ga copper wires to the tabs.

Step 4: Make the Top Ring Assembly

The top ring assembly is made just like the spider frame assembly- it's cut from 22ga steel sheet but you could also use brass sheet or plastic. I oxidized my steel assembly to get the black finish but a sharpie pen or black paint would also work. There are three 3mm bolts that go through the spider and slotted ring- there is a nut on the backside so the assembly stays put when everything is put together in the final assembly.

Step 5: Testing and Final Assembly

Plug in your battery and make sure all your LED's light up. Then mount the center top ring assembly to the inner ring assembly by lining up the three bolts and tightening them until the bottom of the top ring assembly sits just above the inner ring assembly. You can add a dab of glue if you want to the bolts to make sure they don't come loose.

Now press the entire assembly into the backplate assembly- note the orientation, making sure everything is aligned correctly. If the fit is really loose, you can put a couple dabs of glue between the wrapped copper wire sections and the backplate to hold everything together.

There is a central ring that is made from aluminum but it could also be made from plastic and painted silver. It's held on with some thin copper wire and a few dabs of glue from a glue gun.

The last bit is a coil of coper wire that has been formed into a ring. I used wire that was coated red- you could use a marker to color the wire. The wire was wound around a drill bit, formed into a circle and then glued together with a glue gun. The coil ring is then placed around the bolts.