For an S-R latch (with NAND gates), what is the next state of Q' if S=0...

Question

Question

For an S-R latch (with NAND gates), what is the next state of Q' if S=0 and R=1? A. Q(t+1)=1 B. No change C. Q(t+1)=0 D. Forbidden

Answer 1

Answer #1

Answer 2

Similar Homework Help Questions

Below is the diagram for an S-R Latch using NAND gates. Assume the NAND gates each...

Below is the diagram for an S-R Latch using NAND gates. Assume the NAND gates each have 15 nS propagation delay. The system starts with the conditions -S is HIGH, R is HIGH, Q is LOW, and Q is HIGH state, and has been stable in that state for a significantly long time. Now, at some time to, we bring the “S input to the zero state. How long before NOT Q is valid (in a final stable state)? S...
5. Below is the diagram for an S-R Latch using NAND gates. Assume the NAND gates...

5. Below is the diagram for an S-R Latch using NAND gates. Assume the NAND gates each have 15 nS propagation delay. The system starts with the conditions ~S is HIGH, R is HIGH, Q is LOW, and Q is HIGH state, and has been stable in that state for a significantly long time. Now, at some time to, we bring the ~S input to the zero state. How long before NOT Q is valid (in a final stable state)?...
a) Draw an SR-latch using only NAND gates. Label each input and output, and label all...

a) Draw an SR-latch using only NAND gates. Label each input and output, and label all wires with a name if the wire does not connect to any input or output b) Describe the behavior of the latch when S and R are both 0. What is the output of each gate? c) Assuming that the latch starts with S = R = 0, write down the sequence of what happens when R = 1. Discuss changes at each point...

Implement an S-R latch using NOR gates instead of NAND. Which are the outputs for the...

Implement an S-R latch using NOR gates instead of NAND. Which are the outputs for the four possible input scenarios?
1-3(0). Figure 1 the stable state shown in FIGURE 11-3 Cengage Learning 2014 0 0 0 RSO FIGURE 11-4 Cengage Learning 201...

1-3(0). Figure 1 the stable state shown in FIGURE 11-3 Cengage Learning 2014 0 0 0 RSO FIGURE 11-4 Cengage Learning 2014 0 0 Study Section 11.2, Set-Reset Latch. (a) Build an S-R latch in SimUaid, using NOR gates as in Figure 11-3. Place switches on the inputs and probes on the outputs. Experiment with it. Describe in words the behavior of your S-R latch (b) For Figure 11-4(b), what values would P and Q assume if S = R...
What is the term for a set of flip-flops and the gates that implement their state...

What is the term for a set of flip-flops and the gates that implement their state transitions? 1. (a) Full Adder 2. (b) Moore machine 3. (c) Register 4. (d) Decoder 5. (e) None of (a) through (d) is the correct answer. A D flip-flop has a D latch and a SR latch. The D latch is connected directly to the clock (no inverter). This type of flip-flop will be able to change state when the clock is 1. (a)...

Use the gated SR latch design with only NAND gates to design a gated SR flip–flop....

Use the gated SR latch design with only NAND gates to design a gated SR flip–flop. The stored bit Q can only change on the positive edge (rising edge) of the clock cycle. Draw the circuit using only logic gates and create a symbol for the flip–flop you designed.
10.5 This refers to the S' input for the NAND version, i.e., you don't have to...

10.5 This refers to the S' input for the NAND version, i.e., you don't have to include an inverter for S. 10.8 Start with Q = 0, Q = 1. Hint: be sure to remember what you observed in the previous problem! 10.5 → Would you expect the propagation delay from the set input to the Q output to be faster in a set-reset latch built from a pair of NAND gates or one built from a pair of NOR...
Part A: • Determine the next value of Q for the given values of S and...

Part A: • Determine the next value of Q for the given values of S and R. S = 0, R = 1 • Assume that the present value of Q can be either 0 or 1. Note: Qt denotes the next value of Q. RO a) Q+ = 0 b) Q+ = 1 C) Q and Q’ do not change. d) Q and Q’ toggle. e) None of the above. $ 0 Dos not SR Latch Part B: •...

Answers are at the end of the chapter 1. If an S-R latch has a 1...

Answers are at the end of the chapter 1. If an S-R latch has a 1 on the S input and a 0 on the R input and then the S input goes to 0, the latch will be (a) set (b) reset (c) invalid (d) clear 2. The invalid state of an S-R latch occurs when (c) S 1,R-1 (d) S-0, R-O 3. For a gated D latch, the output always equals the D input (a) before the enable...