Implement this circuit and you will get AC Sine Wave from Output with DC square wave as input from astable multivibrator.
Design a DC to AC circuit (must convert square wave to sine wave), using 555 timers,...
(5pts) 11. A 0.5V peak-to-peak 1kHz sine wave with a 100mV DC offset is provided as the input into a non- inverting operational amplifier with a gain of 20. If the output of the op-amp is read using an oscilloscope with AC coupling, then the value is close to a. 2V DC b. 2V peak-to-peak 1kHz sine wave c. 10V peak-to-peak 1kHz sine wave with 2V DC offset d. 10V peak-to-peak 1kHz sine wave only (5pts) 12. Which of the...
1. Power supply (ac to dc) design. [10 pts.] Design a full-wave bridge rectifier circuit to deliver 10 volts dc with less than 0.1 volt (peak to peak) ripple into a load drawing up to 10 mA. (a) Choose the appropriate ac input voltage from the transformer secondary assuming the usual voltage drops for silicon diodes. (b) Determine the correct capacitor value to ensure the specified ripple in your calculation (c) What fuse value should you select for the primary...
A) Draw the circuit diagram and design a half wave rectifier AC-DC converter to deliver 12V-DC with a ripple of 10 mV for a load current of 0.5 A - Design means to find the capacitor value and the ratio of the turns in the transformer assuume the supply voltage is 120v and 60Hz B) Calculate the Peak Inverse Voltage, average and max current through the diode.
i. Draw the circuit (using op-amps) that you would use to generate a square wave. ? ii. Derive expressions for T H, TL, duty cycle and the frequency of the generated square wave. Clearly sketch the different waveforms in your circuit? iii. Let’s assume that in your design you can only use 10k Ω resistors. Choose the values of the other circuit components in your design such that the square wave has a frequency of 1kHz , and a duty...
Design an op-amp circuit using 741 op-amps to do the following; Input range: -300mV to 100mV (note the input is 400mVpp sine wave with 100mV offset) output range: 0V to 5V (Note: a -300mV input should generate a 0V output and a 100mV input should generate a +5V output.) Please use the free online versions of Multisim or PartSim.
Using Op-Amps, design a circuit to have the following transfer function: H (s) = Kps + Ki Where Kp 3.12, Ki 2346. a) b) c) Construct the s-domain circuit of the controller. Find the voltage the controller transfer function in terms of R's and C's. Choose the component values to match the transfer function. The design components must have standard values. d) We have a RL load of R 332 and L-12 mH, we want the current to be a...
Design a FULL WAVE BRIDGE RECTIFIER circuit that will: Take 120volts ac, 60 hz, sinusoidal waveform from the wall power and convert it to a “regulated” dc value giving 15 volts +, - 1.0 volts across a 1200-ohm output load resistor with no more than 2% ripple voltage, all at a total component parts cost of less than $175.00 (US$). Your design process/ analysis is to be conducted by hand. Consider for this design task: Assume an ideal transformer and...
Op Amp Integrators and Differentiators 1.) Design an op-amp circuit that acts as an integrator. Chose R and C values to give you a gain of 5 at f-1kHz Draw out the circuit and show the input and output, label all the pin numbers and show where the +-12 power supply connections for the chip are. Turn in the circuit diagram, carefully labelled 2.) Build your circuit and measure the gain as a function of frequency. Collect enough data to...
Design a three-phase DC to AC converter and show phase-A using IGBT and diodes in simulink