The system bus includes a control bus, an address bus, and a data bus. Explain why the system bus needs all three buses, and for each of the three buses, explain its role in transporting data.
The system bus is a physical component of a computer system which connects the microprocessor to main memory of the system to carry data between them. The bus provides a path for the data and control signals to move between the components of the computer system.
System bus contains 3 main buses for communication between the CPU, IO and the memory
1. Address Bus: As the name suggest, it is used for the purpose of sharing address between different components of the system. It has following major purpose.
2. Data Bus: To send the data from CPU to memory or back to the CPU we need to have Data Lines.
3. Control Bus: This is bus through which we can send signals between different components of the computer.
Hope it clears your doubt :) , and you like it.
The system bus includes a control bus, an address bus, and a data bus. Explain why...
Which BUS defines the size of the processor? a. The system bus. b. The data bus. c. The address bus. d. The control bus. What are the two main parts, the 8086 CPU is divided into? a. Control Unit and Registers. b. ALU and Control Unit. c. Memory and I/O. d. Bus interface unit (BIU) and Execute unit (EU). Typically, a BUS consists of multiple communication paths or lines. Each line is capable of transmitting a signal representing binary 1...
Consider the organization of address bus and data bus in the following two ways • The address bus operates in parallel with the data bus • The address bus is multiplexed with the data bus i) Compare and contrast the two modes of operations. You should briefly explain their advantages and disadvantages. ii) With the aid of a diagram, explain what is burst mode and how burst mode can improve the efficiency of address buses. b) A machine is running...
Design a computer system with an 8-bit address bus, an 8-bit data bus and it uses isolated I/O. It has: 1128 bytes of PROM starting at address 00H (H meaning in hexadecimal) constructed usin ( one 64x8 chip and multiple 32x2 chips; g (2) 96 bytes of RAM constructed 32x4 chips; (3) an output device with a READY signal at address ABH; (4) an input device with a READY signal at address CDH; (5) a bidirectional input/output device with a...
Design a 4KB memory system that has 16-bit data bus and 16-bit address bus, using 1024x8 chips. Draw the chips, address connections, data connections, CS logic (active low).
8. Given this memory chip, design a memory for a CPU with 212 1-byte data words (9 points). do al d38 data lines d4 a3 a4 a5 (Data bus) 13 address linesa6 d6 d? (Address bus) ) as a9 a10 al1 C Output enable write enable Control lines Control bus) --C1 Chip select 8. Given this memory chip, design a memory for a CPU with 212 1-byte data words (9 points). do al d38 data lines d4 a3 a4 a5...
The single-line diagram of a four-bus system and its bus impedance matrix are shown below BUS 2 0.25 j0.2 0.125 0.25 0.4 BUS 3 BUS 1 BUS 4 j0.1 0.1 j0.2 j0.2 ground is the reference node) 0.25 0.2 0.16 0.14 0.2 0.23 0.15 0.151 ZBUs =기0.16 0.15 0.196 0.1 0.14 0.151 0. 0.195 A solid three-phase fault occurs at bus 2 of the network. (a) Calculate the initial symmetrical RMS current in the fault. (b) Determine the voltages during...
In the computer system, the bus is said to be a collection of wires through which data is transmitted. The bus could be unidirectional or bidirectional depending on what is being done at a time. With referenced to the type of buses explain this phenomena or principle.
Problem #1: Take a two-bus system. Bus #1 is represented as an infinite bus with a constant voltage of 120 per unit. Bus #2 is represented as a load / PQ bus with a constant complex power draw (consuming power from system) of 125MW and-55MVAR. The power base for this system is 100MVA. The transmission line between buses #1 and #2 is represented by the pi-model. The series admittance between the buses is Y12-5-12.5pu. The shunt admittance at either end...
The single-line diagram of a three-phase live-bus power system is shown in Fig. 1. All lines have an impedance 0.0099 + 0.0990j pu. Line charging admittance can be neglected. a) Find the Ybus matrix of this system. b) Classify the buses in this system as slack, PV or PQ bus. c) For each bus, state the given and unknown power how variables. d) Find the net power Injection (scheduled power) for buses 2, 3, 4, and 5.
The six-bus system shown in Figure 1 will be simulated using MATLAB. Transmission line data and bus data are given in Tables 1 and 2 respectively. The transmission line data are calculated on 100 MVA base and 230 (line-to-line) kV base for generator. Tasks: 1. Determine the network admittance matrix Y 2. Find the load flow solution using Gauss-Seidel/Newton Raphson method until first iteration by manual calculation. Use Maltab software to solve power flow problem using Gauss-Seidel method. Find the...