5. Figure 1 shows a gear train consisting of a pair of helical gears and a pair of bevel gears Th...
Homework 6: The figure below shows a gear train where gear 1, on shaft a (input shaft), drives gear 2 with 32 teeth (denoted 32T) on shaft b, gear 3 (20T) also is on shaft b and drives gear 4 (507) on shaft c (output shaft). The pitch diameter of gears 1 and 2 are d = 24 mm and d = 48 mm. The center distance between gears 3 and 4 (distance between shafts b and c is 70mm....
Figure Q1 shows a gear train consists of four spur gears A, B, C and D to be designed for a specific mechanism. The power transmitted by gear A is 5 kW at rotational speed of 720 rpm counterclockwise direction. Number of teeth (N) for gears A,B,C and D are respectively 20, 50, 30 and 60. The module and pressure angle of the gears are respectively 4 mm and 20o . Determine followings: (a) Tangential and radial forces between gears...
Problem 2: Now assume that a power of H = 3 kW is transmitted between the shafts and gears and the pressure angle of the bevel gears is ø= 20°. Then find: a) Contact forces between the helical and bevel gears b) Reaction forces at bearings C and D. Assume that the thrust forces are taken by the bearing D. m= 6, 32765 -16 m = 2. 12T. 23° F 38 mm) SXBja 540 rev/min 40T EI 27 35 50...
2. Fig.2 shows an epicyclic gear train in which the internal teeth on the gears A and B have the same diametral pitch. Gear A has 88 teeth and gear B has 100 teeth both internally and externally. The sun-wheel C which is keyed to shaft P has 44 teeth and the pinion E keyed to shaft R has 25. There are floating compound planet wheels F, G. The power input to shaft R is 8 kW at 1440 rev/min....
A pair of bevel gears is required to transmit 11 kW at 500 r.p.m. from the motor shaft to another shaft, the speed reduction being 3 : 1. The shafts are inclined at 60º. The pinion is to have 24 teeth with a pressure angle of 20º and is to be made of cast steel having a static stress of 80 MPa. The gear is to be made of cast iron with a static stress of 55 MPa. The tooth...
The figure shows a pair of shaft-mounted spur gears having a diametral pitch of 5 teeth/in with an 18-tooth 20° pinion driving a 50-tooth gear. The horsepower input is 31 maximum at 1.600 rev/min. Find the magnitude of the maximum forces acting on bearings A,B, C, and D 3 in 3 in RA RB = lbf lbf lbf lbf RD = The figure shows a pair of shaft-mounted spur gears having a diametral pitch of 5 teeth/in with an 18-tooth...
Problem 1 (50 points The planetary gear train shown in the figure uses spur gears with standard, involute teeth cut with a 20° pressure angle and a diametral pitch of 10 teeth/inch. Note that the contact between the gears is indicated by the pitch circles in the figure. a) Gear #2 has 18 teeth and gear #5 has 42 teeth. How many teeth must be on gear #4? b) If the arm (#3) is driven at 600 revolutions per minute...
Desgin 0.2) Figure Q.2 shows a drive system in which a 20-hp electric motor drives separate output shafts. Gear A is mounted on the motor shafit that has a rotational spoed or 1750 rpm clockwise. Gear A drives gear train consisting of…B,C,and D thr deliver power through the shafts on which they are mounted. All gears have a diametral pitch of Pa-8.The following data are given Power delivered by gears B, C, and D: Pa Numbers of teeth for all...
4. Gear bending stress. Consider just the pair Gear 1 and 2. Gears are all 20º pressure angle with a milled profile and a face width of ¼”. Let the transmitted load be 14.0 lbf and the pitch-line velocity be 1178 ft/min. a) What is Y for 20 and 80 teeth? b) What is Kv? c) What is the bending stress on Gear 1, in psi? d) What is the bending stress on Gear 2?
Desgin 0.2) Figure Q.2 shows a drive system in which a 20-hp electric motor drives separate output shafts. Gear A is mounted on the motor shafit that has a rotational spoed or 1750 rpm clockwise. Gear A drives gear train consisting of…B,C,and D thr deliver power through the shafts on which they are mounted. All gears have a diametral pitch of Pa-8.The following data are given Power delivered by gears B, C, and D: Pa Numbers of teeth for all...