Question Water at an average temperature of 110°C and an average velocity of 3.5 m/s flows through a 5-m-long Beryllium Copper (k-66 w/m.k) tube merge in a boiling water tank. Do NOT ignore the wall...
Water at an average velocity of 3.5 m/s flows through a 5-m-long stainless steel tube (k = 14.2 W/m °C) in a boiler. The inner and outer diameters of the tube are Di = 1.0 cm and Do = 1.4 cm, respectively. If the convection heat transfer coefficient at the outer surface of the tube where boiling is taking place is ho = 8400 W/m2 • °C, determine product of the overall heat transfer coefficient Ui by the inner surface...
Water flows through a 0.5 mm thick tube ( thermal conductivity of 16 W/m..C) with a inner diameter of 1.5 cm at 70°C such that the convective heat transfer coefficient is 3500 W/m² . •C. Let us consider the outside of the tube is 20oC and it loses heat by free convection with ho=7.6W/m² • •C. a. Draw the schematic diagram of the process b. Find out which one is the controlling resistance c. Calculate the overall heat-transfer coefficient per...
For such aircraft application (Figure 3), a wall is made from insulation material (k-0.030 W/m.K) and the insulation material is mounted between four layers of carbon steel (2 mm thickness), the carbon layers are separated by a 2 mm air gap (kair-0.025 W/mK). Figure 3, the thermal conductivity of the carbon steel is (k-15.5 W/m.K). The temperature inside the wall is maintained at 6 °C. The environmental temperature is 24°C. The engineer would like to avoid condensation occurring at outer...
Problem 3 (20 points) A cross-flow heat exchanger consists of a bundle of 32 tubes in a long duct. Hot water at 150°C and a mean velocity of 0.5 m/s enters the tubes having inner and outer diameters of 10.2mm and 12.5mm and has to be cooled to 136°C. The tubes are made of steel of thermal conductivity k-40 W/m.K. Air at 10°c enters the exchanger (unfinned) with a volumetric flow rate of 1.0 m3/s. The convective heat transfer coefficient...
system, hot water at an average temperature of 80°C is flowing through a 15-m section of a cast In a heating iron pipe (k 50 W/m K) whose inner and outer diameters are 4 cm and 5 cm, respectively. The outer surface of the pipe, whose emissivity is 0.75, is exposed to the cold air at 10°C in the basement. with a heat transfer coefficient of 15 W/m2.K. The heat transfer coefficient at the inner surface of the pipe is...
Water enters through a thick-walled tube having inner and outer diameters of 19 and 38 mm and 20 m long The inlet temperature is Tmi=17℃ and outlet temperature is Tmo = 50°C. The outer surface of the tube is well Insulated, and electrical heating within the wall provides for a uniform generation rate of q = 8X105 W/m3. If the inner surface temperature of the tube Ts = 60 °C at the outlet what is the local convection heat transfer...
1. Molten copper flows through a l m long alumina pipe that has an ID of 25 cm and a wall thickness of 5 cm. The molten copper has a temperature of 1,500 °C and the alumina pipe is surrounded by 25 °C air. The thermal conductivity of alumina is 46 W/m °C. The convection heat transfer coefficients are 500 W/m2 °C between the alumina pipe and ambient air and 200 W/m² °C between molten copper and the alumina pipe....
Superheated steam flows steadily through steel tubing (k 35 W/m-K) applying a tube inner surface temperature of 575°C. The tubing has an inner diameter of 300 mm and a wall thickness of 30 mm. Insulation (k 0.10 W/m-K) is applied to the outer surface of the tube while thin aluminum sheet is applied around the insulation as a protective covering. The ambient air at 27°C provides a convection coefficient of 6 W/m2-K. Determine the minimum insulation thickness necessary (mm) to...
blem 4 (20 pts) A square chip that is 12.7mm on a side has a maximum allowable chip operating temperature -75°C. To dissipate heat produced in the chip, a 4 x 4 array of copper (k-400 W/m.K) pin fins is proposed to be etallurgically joined to the outer surface of the chip. The convection coefficient is h-250 W/m'K and ambient air mperature isTo-20°C. The pin fin dimeter is D,-1.5mm and length is L,-16mm. Assuming steady-state uniform chip temperature Te-75°C and...
One end of a long rod 3 cm in diameter is inserted into a furnace with the (3 outer end projecting into the outside air. Once the steady state is reached the temperature of the rod is measured at two points, 15 cm apart and found to be 140°C and 100°C, when the atmospheric air is at 30°C with convection coefficient of 20 W/m2.K. Calculate the thermal conductivity of *.the rod material Consider a stainless steel spoon(k = 15.1 W/m.K), partially...