2. Repeat your decoder design for the word CLUI B E Hint: Each logic function requires at most two gates. 2. R...
2. Make an 8-to-1 multiplexer with a 3-to-8 decoder and two groups of 8 AND gates each, plus an OR gate. The 3-to-8 decoder must be done with hierarchical design and several AND gates. You are strongly advised to use Logic Works 5 or similar circuit design software to create circuit diagrams for this question. For hierarchical design, you can draw over the exported circuit diagram to outline smaller hierarchical parts
Design 3- to – 8 decoder using logic gates with enabler, AND, NOT, etc..? Design 3- to – 8 decoder using only two 2-to-4 decoders graphical blocks, use enabler input? a) Design a 3-bit ripple-carry adder using AND, OR, NOT, EXOR, etc.; include carry-in (Cin), carry-out (Cout) and overflow input/output signals? Note: Design for 1-bit first, then extrapolate to 4-bit using 1-bit full-adder graphical block. Design a 3-bit ripple-carry subtractor using AND, OR, NOT, EXOR, etc..; include carry-in (Cin), carry-out...
Draw the logic diagram of a 2-to-4-line decoder using (a) NOR gates only and (b) NAND gates only. please show the steps
Problem 4.0 (20 Points) Design the segment 'b' of the BCD to 7 segment decoder driver of the common cathode seven segment display. Your design should include the following: Hint th e invalid numbers can be used as don't cares Truth table K-Map Simplified Boolean expression Logic circuit implementation . . Problem 4.0 (20 Points) Design the segment 'b' of the BCD to 7 segment decoder driver of the common cathode seven segment display. Your design should include the following:...
Q2A: Truth tables of three logic functions F1, F2 and F3 given above. Implement the function F1, F2 and F3 using 3 to 8 decoder? (Assume a 3to8 decoder component given to you, if required you may use minimum number of additional logic gates to support your design with 3 to 8 decoder) (Points) Q2B: Write HDL code to implement the above function F1, F2 and F3. All three function should include in on HDL code. In you HDL code use...
3. [20 pts] 8-segment decoder for 8 symbols. Implement (draw logic diagram) the segment 4 of the 8-segment decoder for 8 symbols 0 (a) Using K-map to realize the function q 16 pts) (b) Using a 3-8 decoder and OR gates to realize the function q.[7 pts] (e Using 8-to-1 multiplexer to realize the function 17 pts] Notes: 1. A eight-segment decoder is a combinational circuit with a three-bit input a and a 8-bit output q. Each bit of q...
When your design needs a NAND gate, and you only have OR gates and inverters you could use two OR gates connected V Which of the following are real-world considerations in your design, is about the time it takes to travel through a component None of these Static 1 hazard and static O hazards can be fixed in your design by including all corresponding cov When your design requires a multiplexer, you can implement it by using all of these...
Given the two logic functions: how dol know which logic gotes tc Use y(a, b, c) b(a+ c ) G) Implement y (a, b, c) using the decoder of which the function table is given in Table 1, and any necessary basic logic gates.
2. Design a digital logic circuit to convert part of the output code from part 1. to a binary signal. Use CMOS gates. (hint, the simpler you can get the logic, the less work you will have). You must draw the circuit with transistors In Out DUIi 0111 011 0011 010 0001 001 2. Design a digital logic circuit to convert part of the output code from part 1. to a binary signal. Use CMOS gates. (hint, the simpler you...
Design a Digital combinational logic circuit using logic gates that has 4 inputs and 2 outputs. The circuit: i. Turns on a Red LED if its input is a multiple of 2. (i.e., 0, 2, 4, 6, 8 …..) ii. Turns on a Green LED if its input is a multiple of 3. (i.e. 0, 3, 6, 9) - Draw the truth table for the circuit, bearing in mind that this circuit has 4 inputs and 2 outputs, meaning your...