2- -Study the following high-pass filter circuit, find 5 nF t, 50 kΩ a-The cutoff requency...
3. For the active filter circuit below, complete the following: a) Find the magnitude of the transfer function | H | starting from the nodal equations. b) Find the phase shift of the transfer function (W) c) Find the cutoff frequency fc in Hz d) Is this a high pass or low pass filter? e) Find the passband gain of the filter 62 k2 ANA EVA 22 nF 3.3k f) Given the following input signal: vi(t) = 1.0 sin(2nft +...
Assuming an ideal op-amp (1)find the 3dB frequency of the circuit, if R1=1.5 KΩ, R2=13.2 KΩ, R3=20 KΩ, and C=5 nF 2)Consider the above circuit with the component values: R1=13.2 KΩ, R2= 795.77 Ω, R3=20 KΩ, and C=100 nF. Find the angle of the transfer function in degrees at 2KHz . - C R2 R1 + Vi(jw) Vo R3 H HI-
1- The signal x(t) is applied to a low pass filter with cutoff frequency equal to 1; write a MATLAB code to find and plot X(f), H(f) and the output of the filter Y(f), where x(t) is given below: x(t) -0.5 0.5 2- Apply the signal x(t) in the previous example to a HPF, BPF and BSF and draw the output signal Y(f). 3- Find and Plot the transfer function of BSF.
kindly solve part b, c ,d Q2: For the following high pass filter in Figure 2. Derive a formula for the gain or transfer function T (jw) = Find the condition of an optimal performance with minimum ripple in the passband. Find the cut-off frequency f3dB- Design this filter to have f3dB=100 Hz and maximum gain of 50. R3 nori Figure 2 w win V,
in the circuit below, R=50 ohms, L= 50 mH and C=680 microF determine ping Tool t Tools Help - Mode v Delay - HD SM S In the circuit below, R = 50 Ohms, L = 50 mH and C = 680 uF. Determine: a) The transfer function H(s) b) The resonant frequency in Hertz c) The bandwidth in Hertz d) The upper cutoff frequency in Hertz e) The lower cutoff frequency in Hertz f) Which type of filter is...
Consider the filter shown in Figure P1 a) Show that the circuit behaves as a band-pass fiter. (Hint: Find the transfer for this circuit and show that it has the same form as the transfer function for a band-pass filter.) b) Find the center frequency, bandwidth and gain for this band-pass filter c) Find the cutoff frequencies and the quality factor for this band-pass filter. 10 u.F 5 k2 50mF 16 400 (2 Figure P1
Problem 2 a) Using 5 nF capacitors, design an active broad- band first-order bandreject filter with a lower cutoff frequency of 1000 Hz, an upper cut-off frequency of 5000 Hz, and a pass band gain of 10dB. b) Draw the schematic diagram of the filter. c) Write the transfer function to find H(jωo), where ωo is the center frequency of the filter. d) What is the gain (in decibels) of the filer at the center frequency? e) Using Matlab make...
A- for the low pass filter find the cutoff frequency. B- find the Capacitor and the inductor values at 1 GHz cutoff frequency 3.3150H 3.315 H Z-Boul - 2.652, F And he ? f = 1 GHZ Find Values of L and C?
2.Design a high pass filter with a -3 dB frequency of 1 MHz, using the same parts in problem #1. Sketch the magnitude and phase of the transfer function. Answer Qs 2 only I put 1 for the reference 1.Design a low pass filter with a – 3 dB frequency is 1 MHz. The largest capacitor that I have in my bin is 10 nF. a. Find the transfer function for the circuit and sketch its magnitude and phase that...
Assuming an ideal op-amp find the 3dB frequency of the circuit, if R1=2.4 KS2, R2=13.4 K2, R3=20 KS2, and C=5 nF. HH C R2 R1 + Vi(jw) Vo R3 IH Answer: rad/s Consider the above circuit with the component values: R1=2.4 K12, R2=13.4 KS, R3=20 KN and C=5 nF. Find the DC gain of the circuit. Answer: Consider the above circuit with the component values: R1=13.4 KS, R2= 795.77 12, R3=20 K12, and C=100 nF. Find the angle of the...