Design using Digital Electronics components (MOSFETs, etc)
Design using Digital Electronics components (MOSFETs, etc) Problem 1: Design and implement a 2 by 2...
task 1: In digital electronics and modern computer hardware, a flip-flop is sequential digital circuit used as a basic memory element. It has two stable states and can be used to store state information. One of its states represents '1' while the other represents '0'. The most common types of flip-flops are SR-flip-flop, JK-flip-flop, and D flip-flop. When used in a finite-state machine, the output and next state depend not only on its current input, but also on its current...
1. Design a synchronous 2-bit up-down counter using a T flip flop for the most significant bit and an SR flip flop for the least significant bit; when the input X-1, it should count down and for X-0, it should count up. Use SOP.
1. Design a synchronous 2-bit up-down counter using a T flip flop for the most significant bit and an SR flip flop for the least significant bit; when the input X-1, it should count down and...
Equations may require: Po fCV.2 1. Describe the read operation and write operation for a 6T-SRAM. Also, describe the purpose of Sense-amplifier, Driver and Precharge circuits for the memory made of 6T-RAM. If we have to design 4-GByte SRAM, how many transistor will be required only for the memory? 2. What the advantages and disadvantages bet NOR-based, NAND and T-column decoder? 3. Describe the read and write operation in Flash memory made of floating gate transistor. Draw the figure of...
Objective: Creating a register file (memory) using Verilog. The register file is made up of four registers and each register holds one nibble (half a byte, i.e., four bits) 3. Create a D flip-flop AD flip-flop holds 1 bit of data, and it only changes its data when the clock changes. We want a positive edge triggered flip-flop. Design your Verilog D flip-flop, so we will create them now. Enter the 2 to 4 line decoder. We will need two...
ECE 275 - DIGITAL DESIGN Question 1: (@) Write VHDL code for a 2-to-1 multiplexer. - (6) Implement - using only the Sunction R= ab h + bch' + eg h + 8 h 2-to-1 multiplexers. Use the 2-to-1 multiplexer VHDL description as a component to write VHDL code for the of Sunction R, from Problem 1 circuit design
Digital logic design
Question 2 [4+6=10Marks] I. Implement following function using 16 x 1 multiplexer? F(A,B,C,D) = I l.ec.(D1, D2, D3, D4,10,11,13,15) II. Implement function F given above using 8 x 1 multiplexer?
Introduction The purpose of this project is to design, simulate, analyze, implement, and test a single-supply, multistage, transistor amplifier which fulfills a set of specifications. For this project, the pre-lab shall be treated as your formal design report and therefore must be much more detailed than usual (please see Evaluation heading on the next page of this document). The report shall be submitted to the TA by the deadline. The report is an individual assignment. Specifications • Power supply: +???...
Design a Digital combinational logic circuit using logic gates that has 4 inputs and 2 outputs. The circuit: i. Turns on a Red LED if its input is a multiple of 2. (i.e., 0, 2, 4, 6, 8 …..) ii. Turns on a Green LED if its input is a multiple of 3. (i.e. 0, 3, 6, 9) - Draw the truth table for the circuit, bearing in mind that this circuit has 4 inputs and 2 outputs, meaning your...
Problem 2 Design a BCD counter that uses four(4) T flip-flops using the given table format below. The output signal Y = 0 only during the counter transition from 1001 to 0000, otherwise, Y = 1 (for each valid input). Determine the following: (a) The circuit's state table 14 pts. Present State Next State Output Minterm Flip-Flop Inputs Q8 Q4 Q2 Q1 Q8Q4Q2 Y (m) TQ8 TQ4 TQ2 TQ1 Q1 Required format of the state table in Problem 2(a). Show...
Problem 2 Design a BCD counter that uses four(4) T flip-flops using the given table format below. The output signal Y = 0 only during the counter transition from 1001 to 0000, otherwise, Y = 1 (for each valid input). Determine the following: (a) The circuit's state table Present State Next State Output Minterm Flip-Flop Inputs Q4 Q1 Q4 Q1 Y (m) TQ8 T04 TQ2 T01 14 pts. Required format of the state table in Problem 2(a). Show table grid...