A concentrated force P is applied in the middle of a simply supported beam with the T-shaped cross section shown. The maximum value of the load P so that the normal stress in the beam does not exceed 25 MPa is most closely: 150 mm P 30 mm 4m 4m 120 mm A' B A 40 mm A. 3.1 kN B. 5.8 kN Oc. 2.5 kN D. 4.3 kN A concentrated force P is applied in the middle of a...
The mechanical component shown in the diagram is 200 mm wide and 10 mm thick and is made of aluminum that has a yield stress of 240 MPa. Calculate the maximum safe load P that can be applied if the normal stress in the component must not exceed the material’s yield stress. Include a factor of safety of 3. 50 mm 100 mm 80 mm 25-mm radius (typical) 50 mm
Please show work. M1.13 Force based on inclined plane stresses scenes a 500 P 40 mm a The bar has a 40 mm by 20 mm rectangular cross section. The allowable normal and shear stresses on inclined surface a-a must be limited to 55 MPa and 30 MPa, respectively. Determine the magnitude of the maximum axial force P that can be P (kN) (MPa) applied to the bar, and determine the actual normal and shear stresses acting on inclined plane...
A 25 mm diameter hole will be punched in a 1.6 mm thick, 5052-0 aluminum sheet at room temperature. 190 MPa. Calculate the maximum punch Force. Sut
This bracket is to be built from a 20 mm thick steel plate that is 100mm high and 200mm wide. Calculate neglecting the hold the place of maximum deflection and how much when a load of 1Mpa is applied to the right side of the plate. Then calculate the amount and point of maximum stress including the hole. (20mm diameter for the hole sorry with a center position of 100mm from the left side and 50mm from the bottom) deflection...
A vertical load P = 150 kN is applied to a circular solid shaft which in turn is supported by a circular end cap as shown below. Both members are made of steel with allowable normal stress = 160 MPa, allowable shear stress 100 MPa, and allowable bearing stress 200 MPa. Determine the minimum required diameter of the solid shaft, and the minimum required outer diameter and thickness of the circular end plate. P 150 kN ds d 30 mm...
applied to the cantilever beam. The left end of the beam is fixed. Find the state of stress a 25 pts) Three forces are point a. and show them on the cubic element below. 28 n 170 m 37min 16 imm Iz (m") 32 mm 20mm 425 N 12 AN C A (m2) Normal stress (Equation first) Shear stress (Equation first): n红 Mr. N·m MPa applied to the cantilever beam. The left end of the beam is fixed. Find the...
question 6 of 25 mm is pulled in tension with a 44,500 N force producing only elastic detormation . What is oreonding strain and the length between the gage marks when subjected to this force? Given: elastic modulus of copper is 105 GPa. 5. A 10-mm diameter bar of 1040 carbon steel is subjected to a tensile load of 50,000 N, taking it beyond its yield point. Calculate the elastic recov removal of the tensile load. Given: elastic modulus of...
with steps please!!! Question3 Design a thick-walled metallic cylinder of a 200 mm internal diameter for an internal pressure of 30 MPa such as to provide a factor of safety of 3.0 against any yielding in the cylinder and a factor of safety of 4.0 against ultimate collapse. The yield stress of the material is 480 MPa Use both linear and non-linear stress distribution methods of calculation. Compare and discuss the results. Question3 Design a thick-walled metallic cylinder of a...
Q1. The bar has a diameter of 50 mm. If it is subjected to a force of 1200 N as shown, determine the stress components that act at point A and point B. Also, show the results on a volume element located at this point. 150 mm 200 mm B 30° 1200 N