Homework Answers
Detailed answer of above asked question is solved as below.
Add Answer to:
2 A planetary gear train, in which the numbers of teeth of gears are: Z=30, Z=15,...
Problem 1 (50 points The planetary gear train shown in the figure uses spur gears with...
Problem 1 (50 points The planetary gear train shown in the figure uses spur gears with standard, involute teeth cut with a 20° pressure angle and a diametral pitch of 10 teeth/inch. Note that the contact between the gears is indicated by the pitch circles in the figure. a) Gear #2 has 18 teeth and gear #5 has 42 teeth. How many teeth must be on gear #4? b) If the arm (#3) is driven at 600 revolutions per minute...
Kinematics class 3. (25 POINTS) Planetary gear train analysis: The figure below representsa planetary gear train...
Kinematics class
3. (25 POINTS) Planetary gear train analysis: The figure below representsa planetary gear train used in a drill head. Gear 1 rotates with the input shaft. The ring gear 3 meshes both with gear 5 and gear 6, which are the planets. Gear 2 acts as the carrier for gear 5, the output is the carrier 4 Consider the number of teeth Ni-6, N2 36, N-54, N-24 and No-9 a) Identify how many stages are needed to fully...
In the planetary gear train shown in the figure, gear 2 turns at 500 rpm in...
In the planetary gear train shown in the figure, gear
2 turns at 500 rpm in the direction indicated. Determine the speed
and direction of rotation of arm 6 if gears 5 rotates at 300 rpm in
the same direction as gear 2.
STEP NI 3 5 !! 11 21125) Arm 4 (30) (45) 5050)
UU 7. A planetary gear train is shown in Figure P7. The carrier (link 2) serves...
UU 7. A planetary gear train is shown in Figure P7. The carrier (link 2) serves as the input to the train. The sun (gear 1) serves as the output from the train and has a 1.0-in. pitch diameter with a diametric pitch of 20. Gear 3 has 45 teeth and gear 4 has 20 teeth Gear 5 has 30 teeth and is keyed to the same shaft as gear 4. Gear 5 mates with the ring gear (gear 6),...
2. Fig.2 shows an epicyclic gear train in which the internal teeth on the gears A and B have the same diametral p...
2. Fig.2 shows an epicyclic gear train in which the internal teeth on the gears A and B have the same diametral pitch. Gear A has 88 teeth and gear B has 100 teeth both internally and externally. The sun-wheel C which is keyed to shaft P has 44 teeth and the pinion E keyed to shaft R has 25. There are floating compound planet wheels F, G. The power input to shaft R is 8 kW at 1440 rev/min....
** Not Multiple Choice Section ** 11. [25 points] Consider the planetary gear train shown in...
** Not Multiple Choice Section ** 11. [25 points] Consider the planetary gear train shown in the figure. * Gear E is the driver running at +100 rpm. The Arm (link A) is the output driven link. The ring gear B is fixed. The number of teeth given as: are NE 34 ND 17 Nc 26 a) Determine the number of teeth for the ring gear B. All gears use the same pitch b) Determine the rpm and the direction...
A compound gear train is to be designed as a speed increaser to provide a total increase of speed by 30 to 1 ( 1 %). Use spur gears with a 20° pressure angle and a diametral pitch of 7 teeth/in. Assu...
A compound gear train is to be designed as a speed increaser to provide a total increase of speed by 30 to 1 ( 1 %). Use spur gears with a 20° pressure angle and a diametral pitch of 7 teeth/in. Assume same diametral pitch in both stages. 5 1) Specify appropriate numbers of teeth to minimize the gearbox size while avoiding the interference problem in the teeth. Use full-depth teeth Determine the gearbox outside dimension Y, assuming the wall...
Figure Q1 shows a gear train consists of four spur gears A, B, C and D to be designed for a specific mechanism. The power transmitted by gear A is 5 kW at rotational speed of 720 rpm counterclockwise direction. Number of teeth (N) for gears A,B,C and D ar
Figure Q1 shows a gear train consists of four spur gears A, B, C and D to be designed for a specific
mechanism. The power transmitted by gear A is 5 kW at rotational speed of 720 rpm
counterclockwise direction. Number of teeth (N) for gears A,B,C and D are respectively 20, 50,
30 and 60. The module and pressure angle of the gears are respectively 4 mm and 20o
. Determine
followings:
(a) Tangential and radial forces between gears...
Consider the following drive train. Gears are shown by their pitch diameters. Gear 2 is the...
Consider the following drive train. Gears are shown by their pitch diameters. Gear 2 is the pinion Gear diameter not drawn to scale. N4 Ng No 12 + 3 4 6 N2 5 ng N: Question 1 100 pts All gears have a 5 mm module and 25 degree pressure angle The pinion rotates at 100 RPM and has 10 teeth Each simple gear set has a 10:1 gear ratio. Determine: Pinion pitch diameter (mm) overall train ratio [Choose ]...
2. (20 points) Design a compound, reverted, 20 standard spur gear train for a gear ratio of 70:1. (a) Specify the teeth numbers (2 18 for the pinions); (b) With the diametral pitch of 10 for all...
2. (20 points) Design a compound, reverted, 20 standard spur gear train for a gear ratio of 70:1. (a) Specify the teeth numbers (2 18 for the pinions); (b) With the diametral pitch of 10 for all gears, calculate their outside diameters and the contact ratio for the pair with the larger gear ratio.
2. (20 points) Design a compound, reverted, 20 standard spur gear train for a gear ratio of 70:1. (a) Specify the teeth numbers (2 18 for...
Problem 1 (50 points The planetary gear train shown in the figure uses spur gears with standard, involute teeth cut with a 20° pressure angle and a diametral pitch of 10 teeth/inch. Note that the contact between the gears is indicated by the pitch circles in the figure. a) Gear #2 has 18 teeth and gear #5 has 42 teeth. How many teeth must be on gear #4? b) If the arm (#3) is driven at 600 revolutions per minute...
Kinematics class
3. (25 POINTS) Planetary gear train analysis: The figure below representsa planetary gear train used in a drill head. Gear 1 rotates with the input shaft. The ring gear 3 meshes both with gear 5 and gear 6, which are the planets. Gear 2 acts as the carrier for gear 5, the output is the carrier 4 Consider the number of teeth Ni-6, N2 36, N-54, N-24 and No-9 a) Identify how many stages are needed to fully...
In the planetary gear train shown in the figure, gear
2 turns at 500 rpm in the direction indicated. Determine the speed
and direction of rotation of arm 6 if gears 5 rotates at 300 rpm in
the same direction as gear 2.
STEP NI 3 5 !! 11 21125) Arm 4 (30) (45) 5050)
UU 7. A planetary gear train is shown in Figure P7. The carrier (link 2) serves as the input to the train. The sun (gear 1) serves as the output from the train and has a 1.0-in. pitch diameter with a diametric pitch of 20. Gear 3 has 45 teeth and gear 4 has 20 teeth Gear 5 has 30 teeth and is keyed to the same shaft as gear 4. Gear 5 mates with the ring gear (gear 6),...
2. Fig.2 shows an epicyclic gear train in which the internal teeth on the gears A and B have the same diametral pitch. Gear A has 88 teeth and gear B has 100 teeth both internally and externally. The sun-wheel C which is keyed to shaft P has 44 teeth and the pinion E keyed to shaft R has 25. There are floating compound planet wheels F, G. The power input to shaft R is 8 kW at 1440 rev/min....
** Not Multiple Choice Section ** 11. [25 points] Consider the planetary gear train shown in the figure. * Gear E is the driver running at +100 rpm. The Arm (link A) is the output driven link. The ring gear B is fixed. The number of teeth given as: are NE 34 ND 17 Nc 26 a) Determine the number of teeth for the ring gear B. All gears use the same pitch b) Determine the rpm and the direction...
A compound gear train is to be designed as a speed increaser to provide a total increase of speed by 30 to 1 ( 1 %). Use spur gears with a 20° pressure angle and a diametral pitch of 7 teeth/in. Assume same diametral pitch in both stages. 5 1) Specify appropriate numbers of teeth to minimize the gearbox size while avoiding the interference problem in the teeth. Use full-depth teeth Determine the gearbox outside dimension Y, assuming the wall...
Consider the following drive train. Gears are shown by their pitch diameters. Gear 2 is the pinion Gear diameter not drawn to scale. N4 Ng No 12 + 3 4 6 N2 5 ng N: Question 1 100 pts All gears have a 5 mm module and 25 degree pressure angle The pinion rotates at 100 RPM and has 10 teeth Each simple gear set has a 10:1 gear ratio. Determine: Pinion pitch diameter (mm) overall train ratio [Choose ]...
2. (20 points) Design a compound, reverted, 20 standard spur gear train for a gear ratio of 70:1. (a) Specify the teeth numbers (2 18 for the pinions); (b) With the diametral pitch of 10 for all gears, calculate their outside diameters and the contact ratio for the pair with the larger gear ratio.
2. (20 points) Design a compound, reverted, 20 standard spur gear train for a gear ratio of 70:1. (a) Specify the teeth numbers (2 18 for...
Most questions answered within 3 hours.
-
Question1 ) The STL provides similiar classes called stack and
queue, both of which gave functions...
asked 34 minutes ago -
For Questions 1-4, assume you have 5 bits available:
1. For (positive) integers: What is the...
asked 35 minutes ago -
convert grams into vloume with the density of water being at
.997514 g/cm^3 at 23.1 Celsuis...
asked 2 hours ago -
Foreman company obtained a $20,000, 6% loan on May 1, 2018.
Principal and interest will be...
asked 2 hours ago -
5. Problem 11.05 (Discounted Payback)
eBook
Project L costs $60,000, its expected cash inflows are $14,000
per...
asked 3 hours ago -
1. Which of the following is true about politics and health
organizations?
A. Health organizations are...
asked 3 hours ago -
A space vehicle is coasting at a constant velocity of 18.1 m/s
in the +y direction...
asked 4 hours ago -
5) Use the following balanced equation to answer questions
(a)-(i).
3 Cu(s) + 8 HNO3(aq) →...
asked 4 hours ago -
A three-year maturity bond with a 12% annual coupon rate is
currently traded at par $1000...
asked 4 hours ago -
1.
What is the minimum volume to use in the Spec 20 cuvette in order
to...
asked 5 hours ago -
A builder wants to install wall-to-wall carpeting in a living
room of length 8.87 m and...
asked 4 hours ago -
Organizational change can produce anxiety in those affected by
the change. In what ways can change...
asked 4 hours ago