Design a three-bit counter using D flip-flops that has the following characteristics: When the value of...
Up-Down counter with enable using JK flip-flops: Design, construct and test a 2-bit counter that counts up or down. An enable input E determines whether the counter is on or off. If E = 0, the counter is disabled and remains in the present count even though clock pulses are applied to the flip-flops. If E= 1, the counter in enabled and a second input, x, determines the count direction. If x= 1, the circuit counts up with the sequence...
please show your work 4. Design a sequential circuit using D flip-flops that produces the following state table: 1 Present Next QU Q.Qo Qu Q.Qo 0 00 XX 0 01 00 0 10 01 0 11 0 10 00 01 01 10 10 0 11 11 X XX 1 1 1 There are three bits of state split into a single bit Qu and an unsigned two-bit number Q1 Qo. You may assume that the counter does not start in...
Design a two-bit up/down binary counter using D flip-flops that can count in binary from 0 to 7. When the control input x is 0, the circuit counts down, and when it is 1, the circuit counts up. (a) Obtain the state table of the two-bit counter. (b) Obtain the state diagram (c) Draw the logic diagram of the circuit.
ercise 5 Part One: Sequential Logic ask 5.1,1: Design a 4-bit up/down counter that does not overflow or underflow. That is, counting up is disabled when it reaches its maximum value and counting down is disabled when it reaches its minimum value. Use circuit simulation to verify your design. Task 5.1.2: Design a logic implementation of the Finite State Machine in Fiqure 2.3 using JK flip flops. It can be assumed that unused state combinations may be considered as don't...
Its logic design my sequence is 127605 i need help with all this pages please and thank you 27 60 Experiment 4 Six-State Up-Down Counter 1 Objective To become familiar with the design procedures of a counter, which are applicable to the design of other synchronous sequential circuits. 2 Problem description A six-state up-down counter is to be designed. Three flip-flops with outputs Q2,Qi and Qo are required in the design. As shown in Figure 1, the counter is initialized...
Digital Logic Design Design a 0-9 counter using four D flip flops. The counter should run on the SCLK output of the clock divider. It should have a four-bit binary output that increments from 0 to 9 one step on each clock cycle. When it reaches the value of 9, it should restart a 0 on the next clock cycle. Hint: consider using D flip flops with a reset input and using logic to reset the flip flops when the...
can you help me with this problem by drawing a circuit using D flip flops. Also i need the excitation equations. these are the answers 51 An FSM is defined by the state assigned table in Figure P8.1. Derive a circuit that realizes this FSM using D flip-flops. Present Output state 32.1 00 Next state w=0 20 = 1 Il In 10 11 01 00 11 00 10 01 Figure P8.1 State-assigned table for problems 8.1 and 8.2. 8.1. The...
14? 14. Design a cyclic counter that produces the binary sequence 0, 2, 3,1. o..if the control signal X is 0 but produces the binary sequence 0, 1,3,2.0, if the control signal X is1.Use D flip-flops. (a) Draw the state diagram; (6 points (b) Draw the input, present state-next state, excitation table: (6 points) (c) Derive the minimal SOP expressions for the D inputs of the flip-flops using K-maps. Draw the logic circuit realization of the counter, using only NAND...
(a) Design an asynchronous Binary Coded Decimal (BCD) count-up counter using JK flip-flops. Draw the counter circuit clearly showing the configuration of the JK flip-flops and the necessary logic gate(s). Sketch the input and output waveforms of this counter (7 Marks) (b) The binary up/down counter for a cargo lift controller in a 7-storey building has an up-down (UID) control input and a buzzer output (B). The buzzer will sound B 1) when the lift is at level 1 or...
6. Design a 2-bit binary counter that counts, 0, 1, 2, 3, 0,. Use the 74LS374 IC, which has eight D flip-flops on it. They are positive-edge triggered, but it will not matter at all here You may draw a state diagram and then fill in the table Present State Q(t) Next State (D(t) - Q(t+1)) Q1(t) Qo(t) 7. Design a BCD binary counter that counts from 0 to 9 then back to 0 and repeat, displaying the count on...