Find the answers under criteria (oae 20 log10( )D Problem 1: R Low Pass and High...
Active Low-pass and High-pass Filters for Crossover Circuitry (PSPICE) Design a first order active high-pass filter with cut-off frequency of 1 kHz & gain 20dB. Design a first order active low-pass filter with cut-off frequency of 1 kHz & gain 20dB. Plot the magnitude and phase responses of the active high-pass and low-pass filters you have designed using PSpice (Use UA741 Op amp and ±12V dual supply). Connect your active low-pass and high-pass filters as shown in Fig. 1-b. Assume...
For the low-pass filter circuit shown in Fig 2 3k Ω 200mil in out Fig 2 3.a. Use a 2.2nF capacitor to design a high-pass filter to have a cutoff frequency of Skn Draw a schematic of your design. Show all component values and voltages c. Sketch the frequency response of the voltage gain and phase shift Magnitude dB Frequency Hz Phase Frequency Hz For the low-pass filter circuit shown in Fig 2 3k Ω 200mil in out Fig 2...
For the low-pass filter circuit shown in Fig 2 200mH 3k Ω out in Fig 2 (i) (ii) (iii) Write an expression for the transfer function of the circuit State the value of the dc gain of the filter circuit in dB Calculate the cutoff frequency of the filter b. Sketch the frequency response of the voltage gain and phase shift for the filter shown in Fig 2. Show all the values and required information in both graphs Magnitude Frequency...
200 HZ. 6.25) Design a cascading LC low-pass filter with maxi- mally flat magnitude response. Use a passband of 0 to 5 kHz with 5 kHz cutoff frequency and filter to attenuate all frequencies at and above 10 kHz by at least 30 dB. Use R R1 = 50 2 200 HZ. 6.25) Design a cascading LC low-pass filter with maxi- mally flat magnitude response. Use a passband of 0 to 5 kHz with 5 kHz cutoff frequency and filter...
Problem Consider a voltage amplifier having a frequency response of the low-pass STC 1ype with a de gain of 60 dB and a 3-dB frequency of 1000 Hz Find the gain in dB at f- 10 Hz, 10kHz, 100 kHz, and 1 MHz Problem For the circuit shown below first, evalusteand the coresponding comer froquency. Second evalmt and the corresponding comer froquency. At the end caloulate overall transfer function T(w)= and reurite it in the standard fom ( and draw...
1. The circuit below, which uses one inductor and two identical resistors, (30 pts] can be described as a filter. Using this circuit: a. Determine the transfer function, H(@) = Vout/Vin. b. Determine the magnitude and phase (in terms of R, L, and o) of the transfer function from part a. Now, assume R = 5022 and L = 2mH c. What is the value of the magnitude as 0 0 d. The value of the magnitude as → e....
3. For the active filter circuit below, complete the following: a) Find the magnitude of the transfer function | H | starting from the nodal equations. b) Find the phase shift of the transfer function (W) c) Find the cutoff frequency fc in Hz d) Is this a high pass or low pass filter? e) Find the passband gain of the filter 62 k2 ANA EVA 22 nF 3.3k f) Given the following input signal: vi(t) = 1.0 sin(2nft +...
2.Design a high pass filter with a -3 dB frequency of 1 MHz, using the same parts in problem #1. Sketch the magnitude and phase of the transfer function. Answer Qs 2 only I put 1 for the reference 1.Design a low pass filter with a – 3 dB frequency is 1 MHz. The largest capacitor that I have in my bin is 10 nF. a. Find the transfer function for the circuit and sketch its magnitude and phase that...
please read thr question carefully and answer everything please label answer please asap For the circuit below Design a band-pass (R-C) circuit 30. t that allows frequencies only within the range of 2 KJHz and 4 KHz and allows 31. Assuming the resonant frequency is half-way through the cutoff frequencies, calculate the Quality Facto (Q) for this filter. Is it a Low/Medium/High Q? Sketch the normalized plots of both the high-pass and the low-pass fil provided below ters using a...
The cutoff frequency for RC filters (both low-pass and high-pass) is fe-1/2TRCHz. The cutoff frequency for RL filters (both low-pass and high-pass) is fe-R/2TL Hz. To convert gain H to gain in dB: hrdB) = 20 log 10 H. (Note: Gain is generally unitless, because H-Vout/ yn which has units volts,vots.