4.19 Describe how the unstable condition S= R=1 is avoided in the storage latch of the...
Answers are at the end of the chapter 1. If an S-R latch has a 1 on the S input and a 0 on the R input and then the S input goes to 0, the latch will be (a) set (b) reset (c) invalid (d) clear 2. The invalid state of an S-R latch occurs when (c) S 1,R-1 (d) S-0, R-O 3. For a gated D latch, the output always equals the D input (a) before the enable...
5. Given a S-R latch packed in a chip: a) Is it possible to convert it to a D flip-flop using external logic gates? b) If so, how (show diagram)? if not, why not.
Draw the gate level circuit schematic of a D flip-flop and a T flip-flop based on the cross-coupled NAND latch. Briefly discuss the timing behavior of a D flip-flop, a T flip-flop and a latch. (a) (8 Marks) circuit has three inputs, S, C and C2. S is the control input. When S-O, the circuit behaves like a D flip-flop, and when S-1, the circuit behaves like a T flip-flop. The input characteristics of the circuit are tabulated in Table...
QUESTION 7 A master slave flip flop behaves similarly to a clocked latch, except that the latches output can change only near the rising edge of the clock True False QUESTION 8 Assuming zero setup and hold times, clocked latches and flip-flops produce the same outputs as long as the inputs do not change while the clock is asserted True False QUESTIONS An edge-triggered D flip-flop requires more internal gates than a similar device constructed from a J-K master-slave flip...
a) (5 marks) Explain the difference between a latch, a gated latch and a flip flop. b) (5 marks) A gated SR latch has the following schematic diagram CLK a) Draw a timing diagram showing the Q and Q outputs for the following sequence of inputs: CLK R Assume that the initial state of the outputs is Q 0 and Q 1 c) (5 marks) Draw a schematic diagram for a rising edge-triggered master-slave D flip- flop built using two...
please show all work
JK Flip-Flop S R Flip-Flop From(Q) To (Q+) S 0 0 R T Flip-Flop From(Q) To(Q+) 0 0 JK From(Q 0 To (Q+) 0 -- - c) Complete the timing diagram below. Assume that both of flip-flops are edge triggered. (10 pts) Clock
a) Draw SR latch impeltation in NOR gates provied function table b) Show how D latch (transprent) can be made from NOR gate. SR latch is transprent when it comes to storing data. c) What is limitation of D latch in terms of storing data ? what does it achive for digital terms d) Design a D flip flop that is -ve edge trigged using master slave combination of D latches designed in b) Inverters may be needed.
a) Draw an SR-latch using only NAND gates. Label each input and output, and label all wires with a name if the wire does not connect to any input or output b) Describe the behavior of the latch when S and R are both 0. What is the output of each gate? c) Assuming that the latch starts with S = R = 0, write down the sequence of what happens when R = 1. Discuss changes at each point...
digital system solve Q3andQ4
Done 01. When an inverter is placed between both inputs of an SR. flip-lop, the resulting flip-fop is a (a) JK flip-flop (b) T flip-lop (c) Master Slave JK flip-flop (d) D flip-flop 02. A D flip-flop utilizing a Positive-Giate-Triggered (PGT) Clock is in the CLEAR" stae Which of the following input actions will cause it to change states? NGT stands for Negative-Gate-Triggered (a) CLOCK-NGT, D-O (b) CLOCK-PGT, D- (c) CLOCK- NGT: D- (d) CLOCK- PGT,...
hi i need answers for nos. 18-28.
1. In a counter, a flip-flop output 10. A is a group of flip-flops, each one of which transition serves as a source for triggering other flip-flops, not by the common clock pulses. shares a common clock and is capable of storing one bit of information. A) RAM B) latch A ripple Cring (rather than signal transitions) are referred to as B synchronous D binary C) counter D) register 11. The Characteristic Equation...