please explain why each answer is correct or incorrectHomework Answers
Solution:
Correct option is (A): D Flip Flop Edge Triggered
Explanation:
Assuming y as clock pulse and x as input ant z as output....
Since there is only one input...this means options D and E are eliminated because SR latches have two inputs....
Now Close observations shows that...
On the rising edge of of clock pulse y....
- when the input x is high output z goes high
- also when the input is low the output z goes low
- falling edge has no effect on the output which means circuit is positive edge triggered
- the device holds the value between two positive clock edges
- hence the circuit edge triggered D Flip-Flop
As explained above since the circuit is edge triggered not level triggered. Hence options B is incorrect...
Also since clock is present...this means circuit is a Flip-Flop...hence option C is also incorrect
Add Answer to:
please explain why each answer is correct or incorrect
9. What device does this timing diagram...
Complete the timing diagram of Fig. P4.14b by drawing the waveforms of signals 4.14 The circuit...
Complete the timing diagram of Fig. P4.14b by drawing the
waveforms of signals
4.14 The circuit of Fig. P4.14a contains a D latch, a positive-edge-triggered D flip-flop, and a negative-edge-triggered D flip-flop. Complete the timing diagram of Fig. P4.14b by drawing the waveforms of signals,, and y FI D O Clack Clock Figure P4.14: a. Logic diagram. B. Timing diagram.
a) (5 marks) Explain the difference between a latch, a gated latch and a flip flop....
a) (5 marks) Explain the difference between a latch, a gated latch and a flip flop. b) (5 marks) A gated SR latch has the following schematic diagram CLK a) Draw a timing diagram showing the Q and Q outputs for the following sequence of inputs: CLK R Assume that the initial state of the outputs is Q 0 and Q 1 c) (5 marks) Draw a schematic diagram for a rising edge-triggered master-slave D flip- flop built using two...
1. Write the Boolean expression for each output from the PLA below: F = F G...
1. Write the Boolean expression for each output from the PLA below: F = F G H 2. Draw the block diagram (not logic gates) and the truth table for a 4-1 multiplexer. Label all inputs, outputs and select lines. 3. Explain the problem with the S-R latch and how it is fixed by the J-K flip-flop 4. Write the truth table for a Gated D Latch: 5. Complete the following timing diagram for the rising-edge-triggered D flip-flop: akrrrr G1
23. A J-K flip-flop has a l on the J input and a 0 on the...
23. A J-K flip-flop has a l on the J input and a 0 on the K input. What state is the flip-flop in? (a) Q=1,0-0 (b) Q-1, Q-1 (c) Q-0,Q 1 (d) Q-0,Q-0 -24. On a positive edge-triggered S-R flip-flop, the outputs reflect the input condition when (a) the clock pulse is LOW (b) the clock pulse is HIGH (c) the clock pulse transitions from LOW to HIGH (d) the clock pulse transitions from HIGH to LOW 25. The...
1. The D Flip-Flop ) Look for the datasheet of the 7474 D flip-flop and wire it on the breadboard...
1. The D Flip-Flop ) Look for the datasheet of the 7474 D flip-flop and wire it on the breadboard making sure to supply 5V to both Preset and Clear. Utilize the function generator to provide a Clock signal of 1 Hz: i) Press AMPL and set value to 5 Vpp ii) Press FREQ and set value to 1 Hz ili) Press OFFSET and set value to 2.5 V This Clock signal will be the same for all circuits in...
Options selected are not correct. The waveforms below represent the inputs to a negative edge-triggered J-K...
Options selected are not correct.
The waveforms below represent the inputs to a negative edge-triggered J-K flip-flop. At which point(s) willits Qoutput go HIGH? clock 5 : 1 : 3 : 4 a 2 point 3 points 1 and 4 points 1.3 and 4 D point 2 a.edu/courses/1108356/quizzes/2165131 JavaScripl_6th_Editi. CenturyLink High-S... Solar Home Project... P Piazza Network Desmos | Graphing.. 0 Dashboard Q Digital Systems ! -.. What will happen to the output from a negative edge-triggered J-K flip-flop at...
Answers are at the end of the chapter 1. If an S-R latch has a 1...
Answers are at the end of the chapter 1. If an S-R latch has a 1 on the S input and a 0 on the R input and then the S input goes to 0, the latch will be (a) set (b) reset (c) invalid (d) clear 2. The invalid state of an S-R latch occurs when (c) S 1,R-1 (d) S-0, R-O 3. For a gated D latch, the output always equals the D input (a) before the enable...
QUESTION 7 A master slave flip flop behaves similarly to a clocked latch, except that the...
QUESTION 7 A master slave flip flop behaves similarly to a clocked latch, except that the latches output can change only near the rising edge of the clock True False QUESTION 8 Assuming zero setup and hold times, clocked latches and flip-flops produce the same outputs as long as the inputs do not change while the clock is asserted True False QUESTIONS An edge-triggered D flip-flop requires more internal gates than a similar device constructed from a J-K master-slave flip...
Use the Quartus Prime Text Editor to implement a behavioral model of the D flip-flop described ab...
Use the Quartus Prime Text Editor to implement a behavioral
model of the D flip-flop described above in a file named
d_flops.sv. Specify the D flip-flop’s module according to the
interface specification given in the table below.
Port
Mode
Data Type
Size
Description
RST
in
logic
1-bit
Active high asynchronous reset
CLK
in
logic
1-bit
Synchronizing clock signal
EN
in
logic
1-bit
Synchronous clock enable
D
in
logic
1-bit
Synchronous data input
Q
out
logic
1-bit
Current/present state
Qbar
out...
please answer all thanks very much! Question 3 Shown below is a schematic diagram of a...
please answer all thanks very much!
Question 3 Shown below is a schematic diagram of a counter made up of three JK flip-flops. (d) Shown below is a master-slave D flip-flop. This is made using two gated D latches. The truth table for a gated D latch is also shown below. HIGH J J CLK ас ас ac Truth table: gated D latch D EN D D, Q. D, 0. 0 0 go CLK ΕΝΟ ENO: 0 0 1 0...
Complete the timing diagram of Fig. P4.14b by drawing the
waveforms of signals
4.14 The circuit of Fig. P4.14a contains a D latch, a positive-edge-triggered D flip-flop, and a negative-edge-triggered D flip-flop. Complete the timing diagram of Fig. P4.14b by drawing the waveforms of signals,, and y FI D O Clack Clock Figure P4.14: a. Logic diagram. B. Timing diagram.
a) (5 marks) Explain the difference between a latch, a gated latch and a flip flop. b) (5 marks) A gated SR latch has the following schematic diagram CLK a) Draw a timing diagram showing the Q and Q outputs for the following sequence of inputs: CLK R Assume that the initial state of the outputs is Q 0 and Q 1 c) (5 marks) Draw a schematic diagram for a rising edge-triggered master-slave D flip- flop built using two...
1. Write the Boolean expression for each output from the PLA below: F = F G H 2. Draw the block diagram (not logic gates) and the truth table for a 4-1 multiplexer. Label all inputs, outputs and select lines. 3. Explain the problem with the S-R latch and how it is fixed by the J-K flip-flop 4. Write the truth table for a Gated D Latch: 5. Complete the following timing diagram for the rising-edge-triggered D flip-flop: akrrrr G1
23. A J-K flip-flop has a l on the J input and a 0 on the K input. What state is the flip-flop in? (a) Q=1,0-0 (b) Q-1, Q-1 (c) Q-0,Q 1 (d) Q-0,Q-0 -24. On a positive edge-triggered S-R flip-flop, the outputs reflect the input condition when (a) the clock pulse is LOW (b) the clock pulse is HIGH (c) the clock pulse transitions from LOW to HIGH (d) the clock pulse transitions from HIGH to LOW 25. The...
1. The D Flip-Flop ) Look for the datasheet of the 7474 D flip-flop and wire it on the breadboard making sure to supply 5V to both Preset and Clear. Utilize the function generator to provide a Clock signal of 1 Hz: i) Press AMPL and set value to 5 Vpp ii) Press FREQ and set value to 1 Hz ili) Press OFFSET and set value to 2.5 V This Clock signal will be the same for all circuits in...
Options selected are not correct.
The waveforms below represent the inputs to a negative edge-triggered J-K flip-flop. At which point(s) willits Qoutput go HIGH? clock 5 : 1 : 3 : 4 a 2 point 3 points 1 and 4 points 1.3 and 4 D point 2 a.edu/courses/1108356/quizzes/2165131 JavaScripl_6th_Editi. CenturyLink High-S... Solar Home Project... P Piazza Network Desmos | Graphing.. 0 Dashboard Q Digital Systems ! -.. What will happen to the output from a negative edge-triggered J-K flip-flop at...
Answers are at the end of the chapter 1. If an S-R latch has a 1 on the S input and a 0 on the R input and then the S input goes to 0, the latch will be (a) set (b) reset (c) invalid (d) clear 2. The invalid state of an S-R latch occurs when (c) S 1,R-1 (d) S-0, R-O 3. For a gated D latch, the output always equals the D input (a) before the enable...
QUESTION 7 A master slave flip flop behaves similarly to a clocked latch, except that the latches output can change only near the rising edge of the clock True False QUESTION 8 Assuming zero setup and hold times, clocked latches and flip-flops produce the same outputs as long as the inputs do not change while the clock is asserted True False QUESTIONS An edge-triggered D flip-flop requires more internal gates than a similar device constructed from a J-K master-slave flip...
Use the Quartus Prime Text Editor to implement a behavioral
model of the D flip-flop described above in a file named
d_flops.sv. Specify the D flip-flop’s module according to the
interface specification given in the table below.
Port
Mode
Data Type
Size
Description
RST
in
logic
1-bit
Active high asynchronous reset
CLK
in
logic
1-bit
Synchronizing clock signal
EN
in
logic
1-bit
Synchronous clock enable
D
in
logic
1-bit
Synchronous data input
Q
out
logic
1-bit
Current/present state
Qbar
out...
please answer all thanks very much!
Question 3 Shown below is a schematic diagram of a counter made up of three JK flip-flops. (d) Shown below is a master-slave D flip-flop. This is made using two gated D latches. The truth table for a gated D latch is also shown below. HIGH J J CLK ас ас ac Truth table: gated D latch D EN D D, Q. D, 0. 0 0 go CLK ΕΝΟ ENO: 0 0 1 0...
Most questions answered within 3 hours.
-
1a) According to the ideal gas law, _______________.
a. a gas has infinite volume at absolute...
asked 45 minutes ago -
Oakdale Fashions, Inc. had $245,000 in 2018 taxable income.
Using the tax schedule in Table 2.3...
asked 1 hour ago -
The marketing class at CSUS had an average score of 150. An
educational analyst determined that...
asked 2 hours ago -
Justin Case has purchased a $250 000 home by putting 20 % down
and taking out...
asked 2 hours ago -
1. In a labor market, marginal cost for a firm is
____________.
a. recruiting cost
b....
asked 3 hours ago -
On January 1, 2019, ABC Company issued $60,000,000 of 20-year,
10.5% bonds when the market rate...
asked 3 hours ago -
39.4% of US homes continue to use a landline in addition to cell
phone service. 3...
asked 4 hours ago -
Starting with benzene, synthesize 1-phenyl-1-butyne.
Show intermediates and reagents.
asked 5 hours ago -
Create a 32-run crossed array design with six control factors
and two noise factors such that...
asked 6 hours ago -
A 500g sample of sand from source A has the following amounts
retained on each sieve....
asked 6 hours ago -
In
your own words, please explain the essay by John Keynes wrote "The
End of Laissez...
asked 6 hours ago -
How are the matrix and pixels related? Why are smaller
pixels better for diagnostic quality?
asked 6 hours ago